Шанхайская компания Ячжоу Насосы · Производитель насосов Горячая линия: 021-57775777 Моб.: 15921707645 Эл. почта: 34305982@qq.com
Главная / Центр продукции / санитарный насос / BAW санитарный санитарный насос

BAW санитарный санитарный насос

санитарный насос

The BAW hygienic pump mainly consists of the pump body, pump base, and motor, with each component connected by bolts. The support feet under the base plate can be adjusted as needed, making installation convenient and eliminating the need for a fixed installation base. During installation, the outlet pipe can be installed vertically or horizontally according to different requirements. The mechanical seal can be customized in different materials according to customer requirements. In terms of material selection, all parts that come into contact with the material, such as the pump body, pump cover, and impeller, are made of SUS304 and SUS316L. This significantly enhances wear resistance and lubrication properties, thereby extending the service life.

  • Категориясанитарный насос
  • МодельBAW санитарный санитарный насос
  • Горячая линия021-57775777 / 15921707645
  • E-mail34305982@qq.com

Описание

Product introduction

The BAW hygienic pump mainly consists of the pump body, pump base, and motor, with each component connected by bolts. The support feet under the base plate can be adjusted as needed, making installation convenient and eliminating the need for a fixed installation base. During installation, the outlet pipe can be installed vertically or horizontally according to different requirements. The mechanical seal can be customized in different materials according to customer requirements. In terms of material selection, all parts that come into contact with the material, such as the pump body, pump cover, and impeller, are made of SUS304 and SUS316L. This significantly enhances wear resistance and lubrication properties, thereby extending the service life.

Особенности

  • · This series of pumps is designed with smooth transitions, a rigid structure and thick walls.
  • · During manufacture, the pump body and impeller are integrally precision-cast and all part surfaces are treated; during installation, special fixtures ensure dimensional clearance.
  • · This series of pumps has a simple structure, easy disassembly, low noise, high efficiency and gentle handling of material, meeting food hygiene requirements while preserving the original flavor of the product.
  • · The shaft seal adopts an open structure, so even if there is a small amount of leakage it can be observed in time. Even if it is not noticed in a short time, it will not overflow into the motor, ensuring the service life of the motor.

Applicable range

  • · It conveys milk, beverages, wine and various liquids, and is also indispensable conveying equipment for food, chemical, pharmaceutical and other industries.

Instructions for use

  • · When installing the stainless steel sanitary pump, it is best for the pump to be positioned below the suction liquid level (if installed above the suction level, the pump needs to be primed before starting).
  • · Check whether the impeller rotation direction is correct; whether the inlet and outlet pipe joint nuts are tightened; and whether the sealing ring between the pump cover and pump body is properly seated.
  • · Parts in contact with material should be sterilized with steam before use to ensure food hygiene.
  • · A butterfly valve should be installed at the pump outlet to control the flow. Do not operate under overload for a long time to avoid damaging the motor.
  • · After use, the pump should be immediately CIP-cleaned to prevent material adhesion; if no CIP is available, clean it manually.
  • · When cleaning, first pass hot water through, then disassemble and brush all parts in contact with the material with a brush, then rinse with clean water; after cleaning, reinstall them in sequence.
  • · If material is found dripping on the ground behind the pump casing, it indicates leakage at the shaft seal. Check the mechanical seal device on the shaft; if it is severely worn or the seal is damaged, it should be replaced or ground before use.

Performance parameters

Model

Flow

(m³/h)

Head
(m)

Power

(kW)

Inlet and outlet

(mm)

BAW1-8 1 8 0.37 25/25
BAW3-15 3 15 0.75 38/32
BAW5-25 5 25 1.5 51/38
BAW10-25 10 25 2.2 51/38
BAW15-30 15 30 3 51/51
BAW20-30 20 30 4 51/51
BAW30-36 30 36 5.5 63/57
BAW40-36 40 36 7.5 63/57

Галерея

Похожие товары