شركة شنغهاي يازو للمضخات · شركة تصنيع مضخات متخصصة الخط الساخن: 021-57775777 الجوال: 15921707645 بريد إلكتروني: 34305982@qq.com
الرئيسية / مركز المنتجات / مضخة مغناطيسية / CQB Magnetic Drive Centrifugal Pump

CQB Magnetic Drive Centrifugal Pump

مضخة مغناطيسية

The CQB Magnetic Drive Centrifugal Pump (referred to as the Magnetic Pump) typically consists of an electric motor, a magnetic coupling, and a corrosion-resistant centrifugal pump. Its main feature is the use of a magnetic coupling to transmit power, resulting in completely leak-free operation. When the motor drives the outer magnet of the magnetic coupling to rotate, the magnetic field lines pass through the gap and the isolation sleeve, acting on the inner magnet, causing the pump rotor to rotate synchronously with the motor, transmitting torque without mechanical contact. At the power input end of the pump shaft, since the liquid is enclosed within a stationary isolation sleeve, there is no dynamic seal and therefore no leakage.

  • الفئةمضخة مغناطيسية
  • الطرازCQB Magnetic Drive Centrifugal Pump
  • الخط الساخن021-57775777 / 15921707645
  • البريد الإلكتروني34305982@qq.com

مقدمة المنتج

Product introduction

The CQB Magnetic Drive Centrifugal Pump (referred to as the Magnetic Pump) typically consists of an electric motor, a magnetic coupling, and a corrosion-resistant centrifugal pump. Its main feature is the use of a magnetic coupling to transmit power, resulting in completely leak-free operation. When the motor drives the outer magnet of the magnetic coupling to rotate, the magnetic field lines pass through the gap and the isolation sleeve, acting on the inner magnet, causing the pump rotor to rotate synchronously with the motor, transmitting torque without mechanical contact. At the power input end of the pump shaft, since the liquid is enclosed within a stationary isolation sleeve, there is no dynamic seal and therefore no leakage.

Applicable range

  • · Petroleum, chemicals, pharmaceuticals, smelting, electroplating, environmental protection, food, film processing, water treatment, national defense and other industries.
  • · Conveys flammable, explosive, volatile, toxic, rare and precious liquids and various corrosive liquids.

Instructions for use

  • · The magnetic drive pump should be installed horizontally, not vertically; the plastic pump body must not bear the weight of piping; for special cases requiring vertical installation, the motor must face upward.
  • · When the suction liquid level is above the pump axis, simply open the suction pipeline valve before starting the magnetic drive pump; if the suction liquid level is below the pump axis, the pipeline needs a foot valve.
  • · Before use, the magnetic drive pump should be inspected: the motor fan blades should rotate flexibly without jamming or abnormal noise, and all fasteners should be tightened.
  • · Check whether the motor rotation direction is consistent with the magnetic pump rotation mark.
  • · After the magnetic drive pump motor starts, slowly open the discharge valve; after the pump enters normal working condition, adjust the discharge valve to the required opening.
  • · Before the magnetic drive pump stops working, first close the discharge valve, then close the suction pipe valve.

Precautions

  • · Since the cooling and lubrication of the magnetic pump bearings rely on the conveyed medium, dry running is absolutely prohibited; also avoid no-load running caused by restarting after a power failure during operation.
  • · If the conveyed medium contains solid particles, a filter screen should be added at the magnetic drive pump inlet; if it contains ferromagnetic particles, a magnetic filter should be added.
  • · During use, the ambient temperature of the magnetic drive pump should be below 40°C and the motor temperature rise should not exceed 75°C.
  • · The conveyed medium and its temperature for the magnetic drive pump should be within the allowable range of the pump material. Engineering plastic pumps have a use temperature <60°C and metal pumps a use temperature <100°C.
  • · Conveys liquids with suction pressure not greater than 0.2 MPa, maximum working pressure 1.6 MPa, density not greater than 1600 kg/m³, particle size not greater than 30 × 10⁻⁶ m²/s, and free of hard particles and fibers.
  • · For magnetic drive pumps conveying media prone to sedimentation and crystallization, clean promptly after use and drain the accumulated liquid in the pump.
  • · After the magnetic drive pump has run for 100 hours, disassemble and inspect the wear of the bearings and the end-face rotating ring, and replace parts that are no longer usable.

Performance parameters

 No.  Model

 Flow 

 (m³/h)  

    Head    
   (m)    
Speed
(r/min)

  Power  

  (kW)  

1 CQB32-20-125 3.2 20 2900 1.5
2 CQB32-20-160 32 2.2
3 CQB32-25-200 50 4
4 CQB40-25-105 6.3 12.5 1.1
5 CQB40-25-125 20 2.2
6 CQB40-25-160 32 3
7 CQB40-25-200 50 5.5
8 CQB50-40-85 12.5 8 1.1
9 CQB50-32-105 12.5 1.5
10 CQB50-32-125 20 3
11 CQB50-32-160 32 4
12 CQB50-32-200 50 7.5
13 CQB50-32-250 80 18.5
14 CQB65-50-125 25 20 4
15 CQB65-50-160 32 7.5
16 CQB65-40-200 50 15
17 CQB65-40-250 80 22
18 CQB80-65-125 50 20 7.5
19 CQB80-65-160 32 15
20 CQB80-50-200 50 22
21 CQB80-50-250 80 37
22 CQB100-80-125 100 20 15
23 CQB100-80-160 32 22
24 CQB100-65-200 50 37
25 CQB100-65-250 80 55
26 CQB150-150-200 200 50 55
27 CQB200-200-400 400 32 1450 75

معرض المنتج

المنتجات ذات الصلة