Shanghai Yazhou Pump Manufacturing Co., Ltd. · Fabricante profissional de bombas Linha direta: 021-57775777 Celular: 15921707645 E-mail: 34305982@qq.com
Início / Central de produtos / bomba de esgoto / XWJ New Non-Clogging Pulp Pump

XWJ New Non-Clogging Pulp Pump

bomba de esgoto

The XWJ non-clogging pulp pump is a new energy-saving pulp pump. In practical use it features high efficiency, no or minimal leakage, good anti-clogging, stable operation, high reliability and compact structure. This is mainly reflected in the following aspects: use of semi-open or fully open impellers, adjustable clearance between the wear plate and the front side of the impeller, shaft seals mainly using mechanical seals, and the selection of high-precision bearings and high-quality shaft materials.

  • Categoriabomba de esgoto
  • ModeloXWJ New Non-Clogging Pulp Pump
  • Linha direta021-57775777 / 15921707645
  • E-mail34305982@qq.com

Apresentação

Product introduction

The XWJ non-clogging pulp pump is a new energy-saving pulp pump. In practical use it features high efficiency, no or minimal leakage, good anti-clogging, stable operation, high reliability and compact structure. This is mainly reflected in the following aspects: use of semi-open or fully open impellers, adjustable clearance between the wear plate and the front side of the impeller, shaft seals mainly using mechanical seals, and the selection of high-precision bearings and high-quality shaft materials.

Instructions for use

  • · Before the pump starts, check according to the following requirements;
  • · Whether all bolts are tightened; whether thin oil has been filled into the bearing chamber (the oil level should be at the center of the oil gauge).
  • Whether the motor rotation direction is correct;
  • Whether the inlet valve is fully open;
  • Whether the outlet valve is closed;
  • · Whether the sealing water valve is open; sealing water pressure requirement: working pressure plus (0.3–0.5) kgf/cm².
  • · Concentricity: correct the concentricity of the motor shaft and the pump shaft so that the two shafts form a straight line. The allowable non-concentricity on the outer circles of the two couplings is 0.1 mm, and the uneven tolerance of the end-face gap along the circumference is 0.3 mm (after connecting the inlet and outlet pipelines and trial operation, check again respectively, and it shall still meet the above requirements).
  • · After starting the motor to rated speed, slowly open the outlet valve to the rated working condition (it is advisable for the motor operating current to be 80% of the rated value).
  • · During pump operation, pay attention to the running stability of the pump and the cooling and flushing of the sealing water.
  • · When the pump has been running for a period of time or the head has decreased, attention should be paid to adjusting the clearance at the front side of the impeller, as follows: first loosen all fastening nuts, turn the square-head adjusting screw counterclockwise with the oil gun until the wear plate touches the front side of the impeller, then turn the square-head adjusting screw clockwise back by 1/2 turn (at this time the clearance is 0.8–1 mm), and finally tighten all nuts.
  • · When the pump stops, first close the outlet valve, then turn off the motor power, etc.
  • · When the pump needs to be out of service for a period of time, drain all accumulated liquid from the pump for next use.

Performance parameters

Model

 Flow 

 (m³/h)  

    Head    

   (m)    

 Speed 

 (r/min)  

Matched motor model and power

(kW)

80XWJ25-12.5   25 12.5 1450 Y100L-4/2.2
A 20 10 1450 Y90L-4/1.5
80XWJ25-20   25 20 1450 Y100L2-4/3
A 20 16 1450 Y100L1-4/2.2
80XWJ25-32   25 32 1450 Y132S-4/7.5
A 20 28 1450 Y112M-4/5.5
100XWJ50-20   50 20 1450 Y132S-4/5.5
A 45 18 1450 Y112M-4/4
B 40 16 1450 Y112M-4/4
100XWJ50-32   50 32 1450 Y160M-4/11
A 40 26 1450 Y132S-4/7.5
125XWJ100-20   100 20 1450 Y160M-4/11
A 90 18 1450 Y132M-4/7.5
B 80 16 1450 Y132M-4/7.5
125XWJ100-32   100 32 1450 Y160L-4/15
A 90 28 1450 Y160M-4/11
B 80 26 1450 Y160M-4/11
150XWJ200-20   200 20 1450 Y180M-4/18.5
A 180 18 1450 Y160L-4/15
B 160 16 1450 Y160M-4/11
150XWJ200-32   200 32 1450 Y200L-4/30
A 187 28 1450 Y180L-4/22
B 170 24 1450 Y180M-4/18.5
200XWJ400-20   400 20 1450 Y225S-4/37
A 380 18 1450 Y200L-4/30
B 340 15 1450 Y180L-4/22
200XWJ400-32   400 32 1450 Y250M-4/55
A 375 28 1450 Y225M-4/45
B 340 24 1450 Y225S-4/37

Galeria

Produtos relacionados